Application case study
Compressed air is an essential utility in beverage production. It powers pneumatic equipment throughout the plant and, in many bottling operations, provides the pressure required for bottle blow molding. A leak in the compressor room may be far from the packaging line, but the effects can reach production through pressure loss, additional compressor loading and avoidable energy use.
At one beverage facility, the maintenance team used a HIKMICRO acoustic imaging camera to inspect the compressed air system before leakage developed into a larger operational problem. The survey showed how frequency selection and sound source visualization can turn a difficult search in a noisy compressor room into a focused maintenance task.
The facility operated a centralized compressor room that supplied compressed air to the bottle blow molding process. Compressed-air line pressure was approximately 0.7 to 0.8 MPa. Because bottle formation depends on a stable air supply, a substantial loss could affect pressure availability and increase the risk of an unplanned production interruption.
The maintenance objective was therefore preventive. The team wanted to identify leakage while the system was still pressurized, prioritize the connections most likely to require attention and reduce avoidable compressor load before the loss became large enough to disrupt production.
The compressor room presented several conditions that make conventional leak searches difficult. The space was large, the ceiling was high and some connections were positioned more than two meters above the floor. Multiple compressors, motors and flowing air generated a strong and complex acoustic background. Reflections from hard surfaces added further interference.
Manual listening or feeling for escaping air can reveal a large leak when the technician is already close to it. It is less effective for smaller sources, elevated components or systems with many similar valves and connections. Applying bubble solution point by point would also require time and close access to every candidate location.
A 136-microphone HIKMICRO acoustic imaging camera was used to scan the compressor outlet piping, hose connections, valves and flanges. The camera displayed the acoustic energy as a color overlay on the visible image, allowing the operator to connect a detected sound with a physical component.
The frequency spectrum was important in this environment. Background noise was strongest below 25 kHz, where the running machinery made source localization less stable. The inspection team moved the working band to approximately 30 to 40 kHz. This reduced interference from the dominant plant noise and produced more repeatable localization of the candidate leakage points.
This step illustrates a practical advantage of acoustic imaging. The operator is not limited to listening for a leak within the same frequency range as the surrounding machinery. An adjustable band can be used to focus the inspection on a range where the leakage signature is easier to separate from the background.
The survey found five repeatable acoustic hotspots that warranted further inspection.
The acoustic image did more than indicate that compressed air was being lost somewhere in the room. It connected each candidate signal to a visible component, giving the maintenance team a shorter and more practical list of locations to confirm and repair.
Compressed air leaks increase the amount of compressor output required to maintain system pressure. In a bottle blowing application, the operational consequence can extend beyond energy waste. If total leakage grows, pressure stability and production continuity may also be affected.
Acoustic imaging changes the timing of the maintenance response. Instead of waiting for a large leak to become obvious or for pressure loss to interrupt the process, technicians can screen the pressurized system during a planned inspection. The visual result helps them decide where close-range confirmation and repair should begin.
The field findings also showed where routine surveys should focus. Flexible-hose interfaces, tee connections and valves can experience movement, alignment stress and seal aging. Giving these components greater attention can make future inspection routes more efficient without ignoring the rest of the system.
The same approach can be incorporated into routine compressed air maintenance:
Acoustic imaging depends on a pressure differential and on the leak producing detectable airborne sound. A hotspot identifies a candidate source area rather than the root cause of the component failure, and the absence of a hotspot does not by itself prove that a system is leak-free. Acoustic imaging therefore works best as a fast screening step within the existing maintenance workflow.
HIKMICRO AI Series acoustic imaging cameras combine low-noise MEMS microphone arrays with adjustable frequency filtering and a visible-image overlay. In this case, the 136-microphone configuration and the ability to move the inspection band away from the strongest background noise were central to obtaining stable, useful results.
For compressed air applications, real-time estimated leakage information can help teams compare candidate locations and prioritize follow-up. Images, video, voice notes and text annotations can preserve the inspection context, while HIKMICRO Analyzer Acoustic supports further review and reporting after the survey.
These capabilities make acoustic imaging particularly useful in compressor rooms and production utilities where many potential leak points must be checked without starting with close-range, point-by-point testing.
The facility's maintenance question was where to begin. By filtering out dominant machinery noise and mapping repeatable acoustic hotspots onto visible components, the inspection narrowed a large compressor-room search to a small number of actionable locations.
For beverage plants that depend on stable compressed air for bottle blow molding and other pneumatic processes, acoustic imaging provides earlier visibility, more focused troubleshooting and better information for preventive maintenance.
Explore the HIKMICRO AI Series for compressed air leak surveys, or contact HIKMICRO to evaluate your plant's inspection environment and workflow.
Hikmicrotech.com would like to use analytics cookies and other similar tracking technologies ("Cookies") to help us improve our website. The Cookies collect information in a way that does not directly identify anyone. For more information about the Cookies we use, see our cookies policy here.